simon
8931912583
Default brightness is ~5%; UART blink mode and green/red pulses mark OTA success or failure. Failed UART uploads skip ESP-NOW distribution. Co-authored-by: Cursor <cursoragent@cursor.com>
107 lines
4.2 KiB
Markdown
107 lines
4.2 KiB
Markdown
# goTool
|
||
|
||
Host-side UART client for the Powerpod **master** ESP.
|
||
|
||
Full system documentation (roles, ESP-NOW, framing, protobuf): [`../main/README.md`](../main/README.md).
|
||
|
||
## Usage
|
||
|
||
```bash
|
||
cd goTool
|
||
go mod tidy
|
||
go run . -port /dev/ttyUSB0 version
|
||
go run . -port /dev/ttyUSB0 clients
|
||
```
|
||
|
||
| Flag | Default | Description |
|
||
|------|---------|-------------|
|
||
| `-port` | (required) | Serial port on master UART (GPIO2/3 adapter) |
|
||
| `-baud` | `921600` | Must match firmware `UART_BAUD_RATE` |
|
||
|
||
### Commands
|
||
|
||
| Command | UART payload | Description |
|
||
|---------|--------------|-------------|
|
||
| `version` | `0x03` | Prints `version` and `git_hash` from firmware |
|
||
| `clients` | `0x04` | Lists slaves registered on the master via ESP-NOW |
|
||
| `unicast-test` | `0x07` | Sends ESP-NOW unicast test to one slave (`-client`, `-seq`) |
|
||
| `test` | — | Run an automated scenario (JSON configs under `testdata/`) |
|
||
| `serve` | — | Web dashboard at `http://localhost:8080` (WebSocket live updates) |
|
||
| `ota` | 16–19 | UART firmware upload to master; firmware then pushes to slaves via ESP-NOW |
|
||
| `ota-progress` | 21 | Query per-slave ESP-NOW OTA progress on the master (`-client N`, default all) |
|
||
| `led-ring` | 8 | LED ring: `-mode clear\|progress\|digit\|blink`, `-progress`, `-digit`, RGB, `-intensity` (0 = ~5 %), `-blink-ms`, `-blink-count` |
|
||
|
||
`clients` requires slaves to have responded to master discover broadcasts first.
|
||
|
||
### Automated tests
|
||
|
||
Bench **configs** (`testdata/configs/`) list network, MACs, and serial ports (`uart.master` for commands, `*_console` for esptool reset). **Scenarios** run UART commands plus optional `reset` steps.
|
||
|
||
```bash
|
||
go run . test -list-configs
|
||
go run . test -config example-lab -scenario smoke
|
||
go run . test -config my-lab -scenario smoke -port /dev/ttyUSB1 -v
|
||
```
|
||
|
||
With a complete bench config, `-port` is optional for `test` (uses `uart.master` from JSON).
|
||
|
||
See [`testdata/README.md`](testdata/README.md) for the JSON schema.
|
||
|
||
### Web dashboard
|
||
|
||
Polls the master over UART and pushes state to the browser via WebSocket (Alpine.js + Bootstrap 5).
|
||
|
||
```bash
|
||
go run . -port /dev/ttyUSB0 serve
|
||
go run . -port /dev/ttyUSB0 serve -addr :8080 -interval 2s
|
||
make gotool-serve PORT=/dev/ttyUSB0
|
||
```
|
||
|
||
Open [http://localhost:8080](http://localhost:8080) — shows master firmware info and the ESP-NOW client table from `CLIENT_INFO`.
|
||
|
||
If the UART device is unplugged or the port disappears, `serve` keeps running and retries on each poll interval; the UI shows **UART off** until the port is available again.
|
||
|
||
The dashboard can configure nodes using the same UART commands as the CLI:
|
||
|
||
| UI action | CLI equivalent |
|
||
|-----------|------------------|
|
||
| Nur Master | `deadzone -set -value N -client 0` |
|
||
| Einzelner Slave | `deadzone -set -value N -client ID` |
|
||
| Alle Slaves | per-slave ESP-NOW (Master bleibt unverändert; CLI `-all` setzt auch den Master) |
|
||
| Unicast test | `unicast-test -client ID` |
|
||
|
||
HTTP API (used by the web UI): `GET/POST /api/deadzone`, `POST /api/unicast-test`, `POST /api/ota` (multipart field `firmware`, max 2 MiB).
|
||
|
||
| UI / API | Behaviour |
|
||
|----------|-----------|
|
||
| Firmware OTA card | Same as `ota` CLI; WebSocket `ota_progress` with `step` `master` (UART) then `slaves` (ESP-NOW) |
|
||
| `POST /api/ota` | Upload `.bin` to master only — slaves are updated by firmware over ESP-NOW after `OTA_END` |
|
||
|
||
```bash
|
||
go run . -port /dev/ttyUSB0 ota build/powerpod.bin
|
||
```
|
||
|
||
Waits for **ready** after start (~30 s erase), sends 200-byte `OTA_PAYLOAD` frames, reads **block_ack** every 4 KiB, then `OTA_END`. The master then distributes to all available slaves (no extra host traffic); **success** is reported only when that finishes. Allow several minutes for large images. Reboot master and slaves to boot the new firmware.
|
||
|
||
```bash
|
||
go run . -port /dev/ttyUSB0 unicast-test -client 16 -seq 42
|
||
```
|
||
|
||
On success the slave serial log should show `UNICAST TEST OK from master … seq=42`.
|
||
|
||
Example output:
|
||
|
||
```
|
||
clients (2):
|
||
[0] id=42 mac=aabbccddeeff ver=1 available=true used=false last_ping=250 last_success_ping=250
|
||
```
|
||
|
||
## Regenerate protobuf
|
||
|
||
From repo root (needs `protoc`, `protoc-gen-go`, and for C also `pip install protobuf`):
|
||
|
||
```bash
|
||
make gotool-proto # Go: goTool/pb/uart_messages.pb.go
|
||
make proto_generate # C: main/proto/*.pb.h, *.pb.c
|
||
```
|