skruecken/powerpods
1
0
Fork 0
Code Issues Pull Requests Actions Packages Projects Releases Wiki Activity
powerpods/components/bma456/bma456_tablet.h
simon e5db0b21c7 Add optional BMA456 accelerometer init on shared I2C bus. 
Probe and configure the sensor when present; log and continue boot if
init fails so boards without BMA456 still run normally.

Co-authored-by: Cursor <cursoragent@cursor.com>
2026-05-18 22:51:32 +02:00

1167 lines
46 KiB
C
Raw Blame History

/**
* Copyright (c) 2023 Bosch Sensortec GmbH. All rights reserved.
*
* BSD-3-Clause
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
*
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
*
* 3. Neither the name of the copyright holder nor the names of its
* contributors may be used to endorse or promote products derived from
* this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING
* IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
* @file bma456_tablet.h
* @date 2023-07-05
* @version V2.29.0
*
*/
/**
* \ingroup bma4xy
* \defgroup bma456_tablet BMA456_TABLET
* @brief Sensor driver for BMA456_TABLET sensor
*/
#ifndef BMA456_TABLET_H
#define BMA456_TABLET_H
#ifdef __cplusplus
extern "C" {
#endif
#include "bma4.h"
/**\name Chip ID */
#define BMA456_TABLET_CHIP_ID UINT8_C(0x16)
/**\name Sensor feature size */
#define BMA456_TABLET_FEATURE_SIZE UINT8_C(50)
/**\name Feature offset address */
#define BMA456_TABLET_ANY_MOT_OFFSET UINT8_C(0x00)
#define BMA456_TABLET_NO_MOT_OFFSET UINT8_C(0x04)
#define BMA456_TABLET_LOW_G_OFFSET UINT8_C(0x08)
#define BMA456_TABLET_TAP_DETECTOR_OFFSET UINT8_C(0x0E)
#define BMA456_TABLET_ORIENTATION_OFFSET UINT8_C(0x28)
#define BMA456_TABLET_CONFIG_ID_OFFSET UINT8_C(0x2E)
#define BMA456_TABLET_AXES_REMAP_OFFSET UINT8_C(0x30)
/**\name Read/Write Lengths */
#define BMA456_TABLET_RD_WR_MIN_LEN UINT8_C(2)
/*! @name Maximum valid read write length is size of config file array */
#define BMA456_TABLET_RD_WR_MAX_LEN ((uint16_t)sizeof(bma456_tablet_config_file))
/**************************************************************/
/**\name Re-map Axes */
/**************************************************************/
#define BMA456_TABLET_X_AXIS_MASK UINT8_C(0x03)
#define BMA456_TABLET_X_AXIS_SIGN_MASK UINT8_C(0x04)
#define BMA456_TABLET_Y_AXIS_MASK UINT8_C(0x18)
#define BMA456_TABLET_Y_AXIS_SIGN_MASK UINT8_C(0x20)
#define BMA456_TABLET_Z_AXIS_MASK UINT8_C(0xC0)
#define BMA456_TABLET_Z_AXIS_SIGN_MASK UINT8_C(0x01)
/**************************************************************/
/**\name Any/no Motion */
/**************************************************************/
#define BMA456_TABLET_ANY_MOT_LEN UINT8_C(4)
#define BMA456_TABLET_NO_MOT_RD_WR_LEN (BMA456_TABLET_ANY_MOT_LEN + BMA456_TABLET_NO_MOT_OFFSET)
/**\name Any/No motion threshold macros */
#define BMA456_TABLET_ANY_NO_MOT_THRES_MSK UINT16_C(0x07FF)
/**\name Position and mask of interrupt behavior and slope */
#define BMA456_TABLET_ANY_NO_MOTION_INTR_BHVR_EN_POS UINT8_C(0x03)
#define BMA456_TABLET_ANY_NO_MOTION_INTR_BHVR_EN_MSK UINT8_C(0x08)
#define BMA456_TABLET_ANY_MOTION_SLOPE_EN_POS UINT8_C(0x04)
#define BMA456_TABLET_ANY_MOTION_SLOPE_EN_MSK UINT8_C(0x10)
/**\name Any/No motion duration macros */
#define BMA456_TABLET_ANY_NO_MOT_DUR_MSK UINT16_C(0x1FFF)
/**\name Any/No motion enable macros */
#define BMA456_TABLET_ANY_NO_MOT_AXIS_EN_POS UINT8_C(0x0D)
#define BMA456_TABLET_ANY_NO_MOT_AXIS_EN_MSK UINT16_C(0xE000)
/**************************************************************/
/**\name Single/Double/Triple Tap */
/**************************************************************/
/**\name Single tap enable macros */
#define BMA456_TABLET_SINGLE_TAP_EN_MSK UINT8_C(0x01)
/**\name Double tap enable macros */
#define BMA456_TABLET_DOUBLE_TAP_EN_MSK UINT8_C(0x02)
/**\name Triple tap enable macros */
#define BMA456_TABLET_TRIPLE_TAP_EN_MSK UINT8_C(0x04)
/**\name Tap averaging enable macros */
#define BMA456_TABLET_TAP_AVG_EN_MSK UINT8_C(0x08)
/**\name Tap output macros */
#define BMA456_TABLET_SINGLE_TAP_OUT_MSK UINT8_C(0x01)
#define BMA456_TABLET_DOUBLE_TAP_OUT_MSK UINT8_C(0x02)
#define BMA456_TABLET_DOUBLE_TAP_OUT_POS UINT8_C(0x01)
#define BMA456_TABLET_TRIPLE_TAP_OUT_MSK UINT8_C(0x04)
#define BMA456_TABLET_TRIPLE_TAP_OUT_POS UINT8_C(0x02)
/**************************************************************/
/**\name Low-G */
/**************************************************************/
/**\name Low-G enable macros */
#define BMA456_TABLET_LOW_G_FEAT_EN_OFFSET UINT8_C(0x03)
#define BMA456_TABLET_LOW_G_EN_POS UINT8_C(0x04)
#define BMA456_TABLET_LOW_G_EN_MSK UINT8_C(0x10)
/**\name Low-g threshold macro */
#define BMA456_TABLET_LOW_G_THRES_MSK UINT16_C(0x7FFF)
/**\name Low-g hysteresis macro */
#define BMA456_TABLET_LOW_G_HYST_MSK UINT16_C(0x0FFF)
/**\name Low-g duration macro */
#define BMA456_TABLET_LOW_G_DUR_MSK UINT16_C(0x0FFF)
/**************************************************************/
/**\name Orientation */
/**************************************************************/
#define BMA456_TABLET_ORIENTATION_OUT_ADDR UINT8_C(0x1E)
/**\name Orientation enable macros */
#define BMA456_TABLET_ORIENT_EN_MSK UINT8_C(0x01)
/**\name Orientation upside/down detection macros */
#define BMA456_TABLET_ORIENT_UD_POS UINT8_C(1)
#define BMA456_TABLET_ORIENT_UD_MSK UINT8_C(0x02)
/**\name Orientation mode macros */
#define BMA456_TABLET_ORIENT_MODE_POS UINT8_C(2)
#define BMA456_TABLET_ORIENT_MODE_MSK UINT8_C(0x0C)
/**\name Orientation blocking macros */
#define BMA456_TABLET_ORIENT_BLOCKING_POS UINT8_C(4)
#define BMA456_TABLET_ORIENT_BLOCKING_MSK UINT8_C(0x30)
/**\name Orientation hold time macros */
#define BMA456_TABLET_ORIENT_HOLD_TIME_POS UINT8_C(6)
#define BMA456_TABLET_ORIENT_HOLD_TIME_MSK UINT16_C(0x7C0)
/**\name Orientation slope threshold macros */
#define BMA456_TABLET_ORIENT_SLOPE_THRES_MSK UINT16_C(0x00FF)
/**\name Orientation hysteresis macros */
#define BMA456_TABLET_ORIENT_HYST_POS UINT8_C(8)
#define BMA456_TABLET_ORIENT_HYST_MSK UINT16_C(0xFF00)
/**\name Orientation theta macros */
#define BMA456_TABLET_ORIENT_THETA_MSK UINT16_C(0x00FF)
/* Orientation output macros */
#define BMA456_TABLET_ORIENT_OUT_POS UINT8_C(0)
#define BMA456_TABLET_ORIENT_OUT_MSK UINT8_C(0x03)
#define BMA456_TABLET_ORIENT_FACEUP_DOWN_POS UINT8_C(2)
#define BMA456_TABLET_ORIENT_FACEUP_DOWN_MSK UINT8_C(0x04)
/**\name Orientation output macros */
/* Bit pos 2 reflects the face-up (0) face-down(1) only if ud_en is enabled */
#define BMA456_TABLET_FACE_UP UINT8_C(0x00)
#define BMA456_TABLET_FACE_DOWN UINT8_C(0x01)
/* Bit pos 0-1 reflects the have the following value */
#define BMA456_TABLET_PORTRAIT_UP_RIGHT UINT8_C(0x00)
#define BMA456_TABLET_LANDSCAPE_LEFT UINT8_C(0x01)
#define BMA456_TABLET_PORTRAIT_UP_DOWN UINT8_C(0x02)
#define BMA456_TABLET_LANDSCAPE_RIGHT UINT8_C(0x03)
/**************************************************************/
/**\name User macros */
/**************************************************************/
#define BMA456_TABLET_TAP_FEAT_OUT_ADDR UINT8_C(0x20)
/**\name Any-motion/No-motion axis enable macros */
#define BMA456_TABLET_X_AXIS_EN UINT8_C(0x01)
#define BMA456_TABLET_Y_AXIS_EN UINT8_C(0x02)
#define BMA456_TABLET_Z_AXIS_EN UINT8_C(0x04)
#define BMA456_TABLET_EN_ALL_AXIS UINT8_C(0x07)
#define BMA456_TABLET_DIS_ALL_AXIS UINT8_C(0x00)
/**\name Feature enable macros for the sensor */
#define BMA456_TABLET_LOW_G UINT8_C(0x01)
#define BMA456_TABLET_ORIENTATION UINT8_C(0x02)
#define BMA456_TABLET_SINGLE_TAP UINT8_C(0x04)
#define BMA456_TABLET_DOUBLE_TAP UINT8_C(0x08)
#define BMA456_TABLET_TRIPLE_TAP UINT8_C(0x10)
/**\name Interrupt status macros */
#define BMA456_TABLET_TAP_OUT_INT UINT8_C(0x01)
#define BMA456_TABLET_ORIENTATION_INT UINT8_C(0x02)
#define BMA456_TABLET_LOW_G_INT UINT8_C(0x04)
#define BMA456_TABLET_ANY_MOT_INT UINT8_C(0x20)
#define BMA456_TABLET_NO_MOT_INT UINT8_C(0x40)
#define BMA456_TABLET_ERROR_INT UINT8_C(0x80)
/******************************************************************************/
/*! @name Structure Declarations */
/******************************************************************************/
/*!
* @brief Any/No motion configuration
*/
struct bma456_tablet_any_no_mot_config
{
/*! Expressed in 50 Hz samples (20 ms) */
uint16_t duration;
/*! Threshold value for Any-motion/No-motion detection in
* 5.11g format
*/
uint16_t threshold;
/*! To enable selected axes */
uint8_t axes_en;
};
/*!
* @brief Tap param settings
*/
struct bma456_tablet_tap_settings
{
/*! Scaling factor for threshold */
uint16_t tap_sens_thres;
/*! Maximum duration after the first tap */
uint16_t max_gest_dur;
/*! Settling time for high frequency acceleration signal */
uint16_t tap_shock_dur;
/*! Minimum quite time between the two gesture detection */
uint16_t quite_time_after_gest;
/*! Wait for the duration set by max_gest_dur after the first tap */
uint16_t wait_for_timeout;
/*! Selection of axis from 3D-acceleration signal vector */
uint16_t axis_sel;
};
/*!
* @brief Tap output state
*/
struct bma456_tablet_tap_output
{
/*! Single tap detected */
uint8_t s_tap;
/*! Double tap detected */
uint8_t d_tap;
/*! Triple tap detected */
uint8_t t_tap;
};
/*!
* @brief Low-G configuration
*/
struct bma456_tablet_low_g_config
{
/*! Threshold value for Low-G feature */
uint16_t threshold;
/*! Hysteresis value for Low-G feature */
uint16_t hysteresis;
/*! Duration in 50Hz samples(20msec) for
* which threshold has to be exceeded
*/
uint16_t duration;
};
/*!
* @brief Orientation configuration structure
*/
struct bma456_tablet_orientation_config
{
/*! Upside/Downside detection */
uint8_t upside_down;
/*! Mode
* Symmetrical (values 0 or 3), High asymmetrical
* (value 1) or Low asymmetrical (value 2)
*/
uint8_t mode;
/*! Blocking mode
* Sets the blocking mode.
* If blocking is set, no Orientation interrupt will be triggered.
* Default value is 3 <20> the most restrictive blocking mode.
*/
uint8_t blocking;
/*! Hold Time
* The number of samples for which the orientation
* should be stable in 50Hz. Resolution: 5 = 100msecs
*/
uint8_t hold_time;
/*! Slope Threshold
* The slope threshold for blocking mode.
* Resolution: 0.4g = 205 lsbs
*/
uint8_t slope_thres;
/*! Hysteresis
* Hysteresis of acceleration for orientation change detection.
* Resolution: 62.5mg = 32 lsbs
*/
uint8_t hysteresis;
/*! Theta
* Coded value of the threshold angle with horizontal
* used in Blocking modes;
* theta = 64 * (tan(angle)^2);
*/
uint8_t theta;
};
/***************************************************************************/
/*! BMA456_TABLET User Interface function prototypes
****************************************************************************/
/**
* \ingroup bma456_tablet
* \defgroup bma456_tabletApiInit Initialization
* @brief Initialize the sensor and device structure
*/
/*!
* \ingroup bma456_tabletApiInit
* \page bma456_tablet_api_bma456_tablet_init bma456_tablet_init
* \code
* int8_t bma456_tablet_init(struct bma4_dev *dev);
* \endcode
* @details This API is the entry point.
* Call this API before using all other APIs.
* This API reads the chip-id of the sensor and sets the resolution.
*
* @param[in,out] dev : Structure instance of bma4_dev
*
* @return Result of API execution status
* @retval 0 -> Success
* @retval < 0 -> Fail
*/
int8_t bma456_tablet_init(struct bma4_dev *dev);
/**
* \ingroup bma456_tablet
* \defgroup bma456_tabletApiConfig Config
* @brief Configuration APIs
*/
/*!
* \ingroup bma456_tabletApiConfig
* \page bma456_tablet_api_bma456_tablet_write_config_file bma456_tablet_write_config_file
* \code
* int8_t bma456_tablet_write_config_file(struct bma4_dev *dev);
* \endcode
* @details This API is used to upload the config file to enable the features of
* the sensor.
*
* @param[in] dev : Structure instance of bma4_dev.
*
* @return Result of API execution status
* @retval 0 -> Success
* @retval < 0 -> Fail
*/
int8_t bma456_tablet_write_config_file(struct bma4_dev *dev);
/*!
* \ingroup bma456_tabletApiConfig
* \page bma456_tablet_api_bma456_tablet_get_version_config bma456_tablet_get_version_config
* \code
*int8_t bma456_tablet_get_version_config(uint16_t *config_major, uint16_t *config_minor, struct bma4_dev *dev);
* \endcode
* @details This API is used to get the config file major and minor information.
*
* @param[in] dev : Structure instance of bma4_dev.
* @param[out] config_major : Pointer to data buffer to store the config major.
* @param[out] config_minor : Pointer to data buffer to store the config minor.
*
* @return Result of API execution status
* @retval 0 -> Success
* @retval < 0 -> Fail
*/
int8_t bma456_tablet_get_version_config(uint16_t *config_major, uint16_t *config_minor, struct bma4_dev *dev);
/*!
* \ingroup bma456_tabletApiConfig
* \page bma456_tablet_api_bma456_tablet_get_config_id bma456_tablet_get_config_id
* \code
* int8_t bma456_tablet_get_config_id(uint16_t *config_id, struct bma4_dev *dev);
* \endcode
* @details This API is used to get the configuration id of the sensor.
*
* @param[out] config_id : Pointer variable used to store the configuration id.
* @param[in] dev : Structure instance of bma4_dev.
*
* @return Result of API execution status
* @retval 0 -> Success
* @retval < 0 -> Fail
*/
int8_t bma456_tablet_get_config_id(uint16_t *config_id, struct bma4_dev *dev);
/**
* \ingroup bma456_tablet
* \defgroup bma456_tabletApiMapInt Map / Unmap Interrupt
* @brief Map / Unmap user provided interrupt to interrupt pin1 or pin2 of the sensor
*/
/*!
* \ingroup bma456_tabletApiMapInt
* \page bma456_tablet_api_bma456_tablet_map_interrupt bma456_tablet_map_interrupt
* \code
* int8_t bma456_tablet_map_interrupt(uint8_t int_line, uint16_t int_map, uint8_t enable, struct bma4_dev *dev);
* \endcode
* @details This API sets/unsets the user provided interrupt to either
* interrupt pin1 or pin2 in the sensor.
*
* @param[in] int_line: Variable to select either interrupt pin1 or pin2.
*
*@verbatim
* int_line | Macros
* ------------|-------------------
* 0x00 | BMA4_INTR1_MAP
* 0x01 | BMA4_INTR2_MAP
*@endverbatim
*
* @param[in] int_map : Variable to specify the interrupts.
* @param[in] enable : Variable to specify mapping or unmapping of interrupts.
*
*@verbatim
* enable | Macros
* --------|-------------------
* 0x00 | BMA4_DISABLE
* 0x01 | BMA4_ENABLE
*@endverbatim
*
* @param[in] dev : Structure instance of bma4_dev.
*
* @note Below macros specify the interrupts.
*
* Feature Interrupts
* - BMA456_TABLET_TAP_OUT_INT
* - BMA456_TABLET_ORIENTATION_INT
* - BMA456_TABLET_LOW_G_INT
* - BMA456_TABLET_ANY_MOT_INT
* - BMA456_TABLET_NO_MOT_INT
* - BMA456_TABLET_ERROR_INT
*
* Hardware Interrupts
* - BMA4_FIFO_FULL_INT
* - BMA4_FIFO_WM_INT
* - BMA4_MAG_DATA_RDY_INT
* - BMA4_ACCEL_DATA_RDY_INT
*
* @return Result of API execution status
* @retval 0 -> Success
* @retval < 0 -> Fail
*/
int8_t bma456_tablet_map_interrupt(uint8_t int_line, uint16_t int_map, uint8_t enable, struct bma4_dev *dev);
/**
* \ingroup bma456_tablet
* \defgroup bma456_tabletApiIntS Interrupt Status
* @brief Read interrupt status of the sensor
*/
/*!
* \ingroup bma456_tabletApiIntS
* \page bma456_tablet_api_bma456_tablet_read_int_status bma456_tablet_read_int_status
* \code
* int8_t bma456_tablet_read_int_status(uint16_t *int_status, struct bma4_dev *dev);
* \endcode
* @details This API reads the bma456 interrupt status from the sensor.
*
* @param[out] int_status : Variable to store the interrupt status read from
* the sensor.
* @param[in] dev : Structure instance of bma4_dev.
*
* @note Below macros are used to check the interrupt status.
*
* Feature Interrupts
* - BMA456_TABLET_TAP_OUT_INT
* - BMA456_TABLET_ORIENTATION_INT
* - BMA456_TABLET_LOW_G_INT
* - BMA456_TABLET_ANY_MOT_INT
* - BMA456_TABLET_NO_MOT_INT
* - BMA456_TABLET_ERROR_INT
*
* Hardware Interrupts
* - BMA4_FIFO_FULL_INT
* - BMA4_FIFO_WM_INT
* - BMA4_MAG_DATA_RDY_INT
* - BMA4_ACCEL_DATA_RDY_INT
*
* @return Result of API execution status
* @retval 0 -> Success
* @retval < 0 -> Fail
*/
int8_t bma456_tablet_read_int_status(uint16_t *int_status, struct bma4_dev *dev);
/**
* \ingroup bma456_tablet
* \defgroup bma456_tabletApiFeat Sensor Feature
* @brief Enables / Disables features of the sensor
*/
/*!
* \ingroup bma456_tabletApiFeat
* \page bma456_tablet_api_bma456_tablet_feature_enable bma456_tablet_feature_enable
* \code
* int8_t bma456_tablet_feature_enable(uint8_t feature, uint8_t enable, struct bma4_dev *dev);
* \endcode
* @details This API enables/disables the features of the sensor.
*
* @param[in] feature : Variable to specify the features which are to be set in
* bma456 sensor.
* @param[in] enable : Variable which specifies whether to enable or disable the
* features in the bma456 sensor.
*
*@verbatim
* enable | Macros
* --------|-------------------
* 0x00 | BMA4_DISABLE
* 0x01 | BMA4_ENABLE
*@endverbatim
*
* @param[in] dev : Structure instance of bma4_dev.
*
* @note User should use the below macros to enable or disable the
* features of bma456_tablet sensor
*
* - BMA456_TABLET_SINGLE_TAP
* - BMA456_TABLET_DOUBLE_TAP
* - BMA456_TABLET_TRIPLE_TAP
*
* @return Result of API execution status
* @retval 0 -> Success
* @retval < 0 -> Fail
*/
int8_t bma456_tablet_feature_enable(uint8_t feature, uint8_t enable, struct bma4_dev *dev);
/**
* \ingroup bma456_tablet
* \defgroup bma456_tabletApiRemap Remap Axes
* @brief Set / Get x, y and z axis re-mapping in the sensor
*/
/*!
* \ingroup bma456_tabletApiRemap
* \page bma456_tablet_api_bma456_tablet_set_remap_axes bma456_tablet_set_remap_axes
* \code
* int8_t bma456_tablet_set_remap_axes(const struct bma4_remap *remap_data, struct bma4_dev *dev);
* \endcode
* @details This API performs x, y and z axis remapping in the sensor.
*
* @param[in] remap_data : Pointer to store axes remapping data.
* @param[in] dev : Structure instance of bma4_dev
*
* @return Result of API execution status
* @retval 0 -> Success
* @retval < 0 -> Fail
*/
int8_t bma456_tablet_set_remap_axes(const struct bma4_remap *remap_data, struct bma4_dev *dev);
/*!
* \ingroup bma456_tabletApiRemap
* \page bma456_tablet_api_bma456_tablet_get_remap_axes bma456_tablet_get_remap_axes
* \code
* int8_t bma456_tablet_get_remap_axes(struct bma4_remap *remap_data, struct bma4_dev *dev);
* \endcode
* @details This API reads the x, y and z axis remap data from the sensor.
*
* @param[out] remap_data : Pointer to store axis remap data which is read
* from the bma456 sensor.
* @param[in] dev : Structure instance of bma4_dev
*
* @return Result of API execution status
* @retval 0 -> Success
* @retval < 0 -> Fail
*/
int8_t bma456_tablet_get_remap_axes(struct bma4_remap *remap_data, struct bma4_dev *dev);
/**
* \ingroup bma456_tablet
* \defgroup bma456_tabletApiAnyMot Any motion Feature
* @brief Functions of Any motion feature of the sensor
*/
/*!
* \ingroup bma456_tabletApiAnyMot
* \page bma456_tablet_api_bma456_tablet_set_any_mot_config bma456_tablet_set_any_mot_config
* \code
* int8_t bma456_tablet_set_any_mot_config(const struct bma456_tablet_any_no_mot_config *any_mot, struct bma4_dev *dev);
* \endcode
* @details This API sets the configuration of any-motion feature in the sensor
* This API enables/disables the any-motion feature according to the axis set.
*
* @param[in] any_mot : Pointer to structure variable to configure
* any-motion.
*
* @verbatim
* -------------------------------------------------------------------------
* Structure parameters | Description
* --------------------------------|----------------------------------------
* | Defines the number of
* | consecutive data points for
* | which the threshold condition
* duration | must be respected, for interrupt
* | assertion. It is expressed in
* | 50 Hz samples (20 ms).
* | Range is 0 to 163sec.
* | Default value is 5 = 100ms.
* --------------------------------|----------------------------------------
* | Slope threshold value for
* | Any-motion detection
* threshold | in 5.11g format.
* | Range is 0 to 1g.
* | Default value is 0xAA = 83mg.
* --------------------------------|----------------------------------------
* | Enables the feature on a per-axis
* axis_en | basis.
* ---------------------------------------------------------------------------
* | Configuration for acceleration
* slope | scope computation.
* ---------------------------------------------------------------------------
* @endverbatim
*
*@verbatim
* Value | axis_en
* ---------|-------------------------
* 0x00 | BMA456_TABLET_DIS_ALL_AXIS
* 0x01 | BMA456_TABLET_X_AXIS_EN
* 0x02 | BMA456_TABLET_Y_AXIS_EN
* 0x04 | BMA456_TABLET_Z_AXIS_EN
* 0x07 | BMA456_TABLET_EN_ALL_AXIS
*@endverbatim
*
* @param[in] dev : Structure instance of bma4_dev
*
* @return Result of API execution status
* @retval 0 -> Success
* @retval < 0 -> Fail
*/
int8_t bma456_tablet_set_any_mot_config(const struct bma456_tablet_any_no_mot_config *any_mot, struct bma4_dev *dev);
/*!
* \ingroup bma456_tabletApiAnyMot
* \page bma456_tablet_api_bma456_tablet_get_any_motion_config bma456_tablet_get_any_motion_config
* \code
* int8_t bma456_tablet_get_any_motion_config(struct bma456_tablet_anymotion_config *any_motion, struct bma4_dev *dev);
* \endcode
* @details This API gets the configuration of any-motion feature from the
* sensor.
*
* @param[out] any_mot : Pointer to structure variable to configure
* any-motion.
*
* @verbatim
* -------------------------------------------------------------------------
* Structure parameters | Description
* --------------------------------|----------------------------------------
* | Defines the number of
* | consecutive data points for
* | which the threshold condition
* duration | must be respected, for interrupt
* | assertion. It is expressed in
* | 50 Hz samples (20 ms).
* | Range is 0 to 163sec.
* | Default value is 5 = 100ms.
* --------------------------------|----------------------------------------
* | Slope threshold value for
* | Any-motion detection
* threshold | in 5.11g format.
* | Range is 0 to 1g.
* | Default value is 0xAA = 83mg.
* --------------------------------|-----------------------------------------
* | Enables the feature on a per-axis
* axis_en | basis.
* ---------------------------------------------------------------------------
* | Configuration for acceleration
* slope | scope computation.
* ---------------------------------------------------------------------------
* @endverbatim
*
*@verbatim
* Value | axis_en
* ---------|-------------------------
* 0x00 | BMA456_TABLET_DIS_ALL_AXIS
* 0x01 | BMA456_TABLET_X_AXIS_EN
* 0x02 | BMA456_TABLET_Y_AXIS_EN
* 0x04 | BMA456_TABLET_Z_AXIS_EN
* 0x07 | BMA456_TABLET_EN_ALL_AXIS
*@endverbatim
*
* @param[in] dev : Structure instance of bma4_dev
*
* @return Result of API execution status
* @retval 0 -> Success
* @retval < 0 -> Fail
*/
int8_t bma456_tablet_get_any_mot_config(struct bma456_tablet_any_no_mot_config *any_mot, struct bma4_dev *dev);
/**
* \ingroup bma456_tablet
* \defgroup bma456_tabletApiNomot No-Motion Feature
* @brief Operations of no-motion feature of the sensor
*/
/*!
* \ingroup bma456_tabletApiNomot
* \page bma456_tablet_api_bma456_tablet_set_no_motion_config bma456_tablet_set_no_motion_config
* \code
* int8_t bma456_tablet_set_no_motion_config(const struct bma456_tablet_nomotion_config *no_motion, struct bma4_dev *dev);
* \endcode
* @details This API sets the configuration of no-motion feature in the sensor
* This API enables/disables the no-motion feature according to the axis set.
*
* @param[in] no_mot : Pointer to structure variable to configure
* no-motion.
* @verbatim
* -------------------------------------------------------------------------
* Structure parameters | Description
* --------------------------------|----------------------------------------
* | Defines the number of
* | consecutive data points for
* | which the threshold condition
* duration | must be respected, for interrupt
* | assertion. It is expressed in
* | 50 Hz samples (20 ms).
* | Range is 0 to 163sec.
* | Default value is 5 = 100ms.
* --------------------------------|----------------------------------------
* | Slope threshold value for
* | No-motion detection
* threshold | in 5.11g format.
* | Range is 0 to 1g.
* | Default value is 0xAA = 83mg.
* --------------------------------|----------------------------------------
* | Enables the feature on a per-axis
* axis_en | basis.
* ---------------------------------------------------------------------------
* @endverbatim
*
*@verbatim
* Value | axis_en
* ---------|-------------------------
* 0x00 | BMA456_TABLET_DIS_ALL_AXIS
* 0x01 | BMA456_TABLET_X_AXIS_EN
* 0x02 | BMA456_TABLET_Y_AXIS_EN
* 0x04 | BMA456_TABLET_Z_AXIS_EN
* 0x07 | BMA456_TABLET_EN_ALL_AXIS
*@endverbatim
*
* @param[in] dev : Structure instance of bma4_dev
*
* @return Result of API execution status
* @retval 0 -> Success
* @retval < 0 -> Fail
*/
int8_t bma456_tablet_set_no_mot_config(const struct bma456_tablet_any_no_mot_config *no_mot, struct bma4_dev *dev);
/*!
* \ingroup bma456_tabletApiNomot
* \page bma456_tablet_api_bma456_tablet_get_no_motion_config bma456_tablet_get_no_motion_config
* \code
* int8_t bma456_tablet_get_no_motion_config(struct bma456_tablet_nomotion_config *no_motion, struct bma4_dev *dev);
* \endcode
* @details This API gets the configuration of no-motion feature from the
* sensor.
*
* @param[out] no_mot : Pointer to structure variable to configure
* no-motion.
*
* @verbatim
* -------------------------------------------------------------------------
* Structure parameters | Description
* --------------------------------|----------------------------------------
* | Defines the number of
* | consecutive data points for
* | which the threshold condition
* duration | must be respected, for interrupt
* | assertion. It is expressed in
* | 50 Hz samples (20 ms).
* | Range is 0 to 163sec.
* | Default value is 5 = 100ms.
* --------------------------------|----------------------------------------
* | Slope threshold value for
* | No-motion detection
* threshold | in 5.11g format.
* | Range is 0 to 1g.
* | Default value is 0xAA = 83mg.
* --------------------------------|-----------------------------------------
* | Enables the feature on a per-axis
* axis_en | basis.
* ---------------------------------------------------------------------------
* @endverbatim
*
*@verbatim
* Value | axis_en
* ---------|-------------------------
* 0x00 | BMA456_TABLET_DIS_ALL_AXIS
* 0x01 | BMA456_TABLET_X_AXIS_EN
* 0x02 | BMA456_TABLET_Y_AXIS_EN
* 0x04 | BMA456_TABLET_Z_AXIS_EN
* 0x07 | BMA456_TABLET_EN_ALL_AXIS
*@endverbatim
*
* @param[in] dev : Structure instance of bma4_dev
*
* @return Result of API execution status
* @retval 0 -> Success
* @retval < 0 -> Fail
*/
int8_t bma456_tablet_get_no_mot_config(struct bma456_tablet_any_no_mot_config *no_mot, struct bma4_dev *dev);
/**
* \ingroup bma456_tablet
* \defgroup bma456_tabletApOP Tap Output
* @brief Functions to provide tap feature output status
*/
/*!
* \ingroup bma456_tabletApOP
* \page bma456_tablet_api_bma456_tablet_tap_output bma456_tablet_tap_output
* \code
* int8_t bma456_tablet_tap_output(struct bma456_tablet_tap_output *out_state, struct bma4_dev *dev);
* \endcode
* @details This API gets the output for tap(single, double, triple) feature.
*
* @param[out] out_state : Pointer variable which stores feature output values.
* @param[in] dev : Structure instance of bma4_dev
*
* @return Result of API execution status
* @retval 0 -> Success
* @retval < 0 -> Fail
*/
int8_t bma456_tablet_tap_output(struct bma456_tablet_tap_output *out_state, struct bma4_dev *dev);
/**
* \ingroup bma456_tablet
* \defgroup bma456_tabletApiTap Tap Feature
* @brief Tap feature operations
*/
/*!
* \ingroup bma456_tabletApiTap
* \page bma456_tablet_api_bma456_tablet_tap_get_parameter bma456_tablet_tap_get_parameter
* \code
* int8_t bma456_tablet_tap_get_parameter(struct bma456_tablet_tap_settings *setting, struct bma4_dev *dev);
* \endcode
* @details This API gets the tap parameter settings.
*
* @param[out] setting : Pointer to structure variable which stores the
* tap parameters read from the sensor
* @param[in] dev : Structure instance of bma4_dev
*
* @return Result of API execution status
* @retval 0 -> Success
* @retval < 0 -> Fail
*/
int8_t bma456_tablet_tap_get_parameter(struct bma456_tablet_tap_settings *setting, struct bma4_dev *dev);
/*!
* \ingroup bma456_tabletApiTap
* \page bma456_tablet_api_bma456_tablet_tap_set_parameter bma456_tablet_tap_set_parameter
* \code
* int8_t bma456_tablet_tap_set_parameter(const struct bma456_tablet_tap_settings *setting, struct bma4_dev *dev);
* \endcode
* @details This API sets the tap parameter settings in the sensor.
*
* @param[in] setting : Pointer to structure variable which stores the
* tap parameter settings read from the sensor.
* @param[in] dev : Structure instance of bma4_dev
*
* @return Result of API execution status
* @retval 0 -> Success
* @retval < 0 -> Fail
*/
int8_t bma456_tablet_tap_set_parameter(const struct bma456_tablet_tap_settings *setting, struct bma4_dev *dev);
/**
* \ingroup bma456_tablet
* \defgroup bma456_tabletApLowG Low-G Feature
* @brief Functions of Low-G feature of the sensor
*/
/*!
* \ingroup bma456_tabletApLowG
* \page bma456_tablet_api_bma456_tablet_set_low_g_config bma456_tablet_set_low_g_config
* \code
* int8_t bma456_tablet_set_low_g_config(const struct bma456_tablet_low_g_config *low_g, struct bma4_dev *dev);
* \endcode
* @details This API sets the configuration of low-g feature of the sensor.
*
* @param[in] low_g : Pointer to structure variable used to
* store the low-g feature settings to be written to the sensor.
*
* Structure members are provided in the table below
*
*@verbatim
* -------------------------------------------------------------------------
* Structure parameters | Description
* --------------------------------|----------------------------------------
* | Threshold value for low-g feature.
* threshold | Range is 0 to 1g.
* | Default value is 512 = 0.25g.
* --------------------------------|----------------------------------------
* | Hysteresis value for low_g feature.
* hysteresis | Range is 0 to 0.5g.
* | Default value is 256 = 0.125g.
* --------------------------------|----------------------------------------
* | Duration in 50 Hz samples (20 msec) for
* duration | which the threshold has to be exceeded.
* | Range is 0 to 82 sec.
* | Default value is 0 = 0 ms.
* --------------------------------|----------------------------------------
*@endverbatim
*
* @param[in] dev : Structure instance of bma4_dev
*
* @return Result of API execution status
* @retval 0 -> Success
* @retval < 0 -> Fail
*/
int8_t bma456_tablet_set_low_g_config(const struct bma456_tablet_low_g_config *low_g, struct bma4_dev *dev);
/*!
* \ingroup bma456_tabletApLowG
* \page bma456_tablet_api_bma456_tablet_get_low_g_config bma456_tablet_get_low_g_config
* \code
* int8_t bma456_tablet_get_low_g_config(struct bma456_tablet_low_g_config *low_g, struct bma4_dev *dev);
* \endcode
* @details This API gets the configuration of significant motion feature
* from the sensor.
*
* @param[out] low_g : Pointer to structure variable used to
* store the low-g feature settings read from the sensor.
*
* Structure members are provided in the table below
*
*@verbatim
* -------------------------------------------------------------------------
* Structure parameters | Description
* --------------------------------|----------------------------------------
* | Threshold value for low-g feature.
* threshold | Range is 0 to 1g.
* | Default value is 512 = 0.25g.
* --------------------------------|----------------------------------------
* | Hysteresis value for low_g feature.
* hysteresis | Range is 0 to 0.5g.
* | Default value is 256 = 0.125g.
* --------------------------------|----------------------------------------
* | Duration in 50 Hz samples (20 msec) for
* duration | which the threshold has to be exceeded.
* | Range is 0 to 82 sec.
* | Default value is 0 = 0 ms.
* --------------------------------|----------------------------------------
*@endverbatim
*
* @param[in] dev : Structure instance of bma4_dev
*
* @return Result of API execution status
* @retval 0 -> Success
* @retval < 0 -> Fail
*/
int8_t bma456_tablet_get_low_g_config(struct bma456_tablet_low_g_config *low_g, struct bma4_dev *dev);
/**
* \ingroup bma456_tablet
* \defgroup bma456_tabletApiOrientation Orientation Feature
* @brief Functions of Orientation feature of the sensor
*/
/*!
* \ingroup bma456_tabletApiOrientation
* \page bma456_tablet_api_bma456_tablet_set_orientation_config bma456_tablet_set_orientation_config
* \code
* int8_t bma456_tablet_set_orientation_config(struct bma456_tablet_orientation_config *orientation, struct bma4_dev *dev);
* \endcode
* @details This API sets the configuration of orientation feature of the sensor.
*
* @param[in] orientation : Pointer to structure variable used to
* store the orientation feature settings to be written to sensor.
*
* Structure members are provided in the table below
*
*@verbatim
* -------------------------------------------------------------------------
* Structure parameters | Description
* --------------------------------|----------------------------------------
* ud_en | Enables face upside/downside
* | detection if set to 1
* --------------------------------|----------------------------------------
* | symmetrical (values 0 or 3),
* mode | high asymmetrical (value 1)
* | or low asymmetrical (value 2).
* --------------------------------|----------------------------------------
* | Sets the blocking mode.
* blocking | Default value is 4, the most
* | restrictive blocking mode.
* -------------------------------------------------------------------------
* | The number of samples for which
* hold_time | the orientation should be stable
* | in 50Hz. Reolution: 5 = 100msecs
* -------------------------------------------------------------------------
* slope_thres | The slope threshold for blocking
* | mode. Resolution: 0.4g = 205 lsbs
* -------------------------------------------------------------------------
* | Hysteresis of acceleration for
* hysteresis | orientation change detection.
* | Resolution: 62.5mg = 32 lsbs
* -------------------------------------------------------------------------
* | Coded value of the threshold angle
* | with horizontal used in blocking
* theta | modes, theta = 64 * (tan(angle)^2).
* | Default value is 40 which is
* | equivalent to 38 degrees angle.
* -------------------------------------------------------------------------
*@endverbatim
*
* @param[in] dev : Structure instance of bma4_dev
*
* @return Result of API execution status
* @retval 0 -> Success
* @retval < 0 -> Fail
*/
int8_t bma456_tablet_set_orientation_config(const struct bma456_tablet_orientation_config *orientation,
struct bma4_dev *dev);
/*!
* \ingroup bma456_tabletApiOrientation
* \page bma456_tablet_api_bma456_tablet_get_orientation_config bma456_tablet_get_orientation_config
* \code
* int8_t bma456_tablet_get_orientation_config(struct bma456_tablet_orientation_config *orientation, struct bma4_dev *dev);
* \endcode
* @details This API gets the configuration of orientation feature from the sensor.
*
* @param[out] orientation : Pointer to structure variable used to
* store the orientation feature settings read from the sensor.
*
* Structure members are provided in the table below
*
*@verbatim
* -------------------------------------------------------------------------
* Structure parameters | Description
* --------------------------------|----------------------------------------
* ud_en | Enables face upside/downside
* | detection if set to 1
* --------------------------------|----------------------------------------
* | symmetrical (values 0 or 3),
* mode | high asymmetrical (value 1)
* | or low asymmetrical (value 2).
* --------------------------------|----------------------------------------
* | Sets the blocking mode.
* blocking | Default value is 4, the most
* | restrictive blocking mode.
* -------------------------------------------------------------------------
* | The number of samples for which
* hold_time | the orientation should be stable
* | in 50Hz. Reolution: 5 = 100msecs
* -------------------------------------------------------------------------
* slope_thres | The slope threshold for blocking
* | mode. Resolution: 0.4g = 205 lsbs
* -------------------------------------------------------------------------
* | Hysteresis of acceleration for
* hysteresis | orientation change detection.
* | Resolution: 62.5mg = 32 lsbs
* -------------------------------------------------------------------------
* | Coded value of the threshold angle
* | with horizontal used in blocking
* theta | modes, theta = 64 * (tan(angle)^2).
* | Default value is 40 which is
* | equivalent to 38 degrees angle.
* -------------------------------------------------------------------------
*@endverbatim
*
* @param[in] dev : Structure instance of bma4_dev
*
* @return Result of API execution status
* @retval 0 -> Success
* @retval < 0 -> Fail
*/
int8_t bma456_tablet_get_orientation_config(struct bma456_tablet_orientation_config *orientation, struct bma4_dev *dev);
/*!
* \ingroup bma422nApiOrient
* \page bma456_tablet_api_bma456_tablet_orientation_output bma456_tablet_orientation_output
* \code
* int8_t bma456_tablet_orientation_output(uint8_t *orientation_output, uint8_t *orientation_faceup_down,
* struct bma4_dev *dev);
*
* \endcode
* @details This API gets the output of orientation feature from the sensor.
*
* @param orientation_output : pointer used to store the orientation output.
*
*@verbatim
* orientation_output | Values
*-------------------------------|-----------------------------
* Bit pos 0-1 reflects | BMA456_TABLET_PORTRAIT_UP_RIGHT
* orientation output value | BMA456_TABLET_LANDSCAPE_LEFT
* only if ud_en is enabled | BMA456_TABLET_PORTRAIT_UP_DOWN
* | BMA456_TABLET_LANDSCAPE_RIGHT
*-------------------------------|-----------------------------
*@endverbatim
*
* @param orientation_faceup_down : Output value of face down face up orientation
*
*@verbatim
* orientation_faceup_down | Values
*-------------------------------|-----------------------------
* Bit pos 2 reflects | BMA456_TABLET_FACE_UP
* face-up (0) or face-down(1) | BMA456_TABLET_FACE_DOWN
* only if ud_en is enabled |
*-------------------------------|-----------------------------
*@endverbatim
*
* @param dev : Structure instance of bma4_dev
*
* @return Result of API execution status
* @retval 0 -> Success
* @retval < 0 -> Fail
*/
int8_t bma456_tablet_orientation_output(uint8_t *orientation_output,
uint8_t *orientation_faceup_down,
struct bma4_dev *dev);
#ifdef __cplusplus
}
#endif /* End of CPP guard */
#endif /* End of header guard macro */
Reference in New Issue View Git Blame Copy Permalink