/**\
 * Copyright (c) 2023 Bosch Sensortec GmbH. All rights reserved.
 *
 * SPDX-License-Identifier: BSD-3-Clause
 **/

#include <stdio.h>
#include <stdlib.h>

#include "coines.h"
#include "bma456_tablet.h"
#include "common.h"

/*********************************************************************/
/* functions */
/*********************************************************************/

/*!
 *  @brief Main Function where the execution getting started to test the code.
 */
int main(void)
{
    int8_t rslt;
    struct bma4_dev bma4;
    struct bma4_remap remap_data = { 0 };
    struct bma4_accel accel = { 0 };
    struct bma4_accel_config accel_conf = { 0 };
    uint16_t int_status = 0;

    char data_array[13][11] =
    { { 0 }, { "BMA4_X" }, { "BMA4_Y" }, { 0 }, { "BMA4_Z" }, { 0 }, { 0 }, { 0 }, { 0 }, { "BMA4_NEG_X" },
      { "BMA4_NEG_Y" }, { 0 }, { "BMA4_NEG_Z" } };

    /* Interface reference is given as a parameter
     *         For I2C : BMA4_I2C_INTF
     *         For SPI : BMA4_SPI_INTF
     * Variant information given as parameter - BMA45X_VARIANT
     */
    rslt = bma4_interface_init(&bma4, BMA4_I2C_INTF, BMA45X_VARIANT);
    bma4_error_codes_print_result("bma4_interface_init", rslt);

    /* Sensor initialization */
    rslt = bma456_tablet_init(&bma4);
    bma4_error_codes_print_result("bma456_tablet_init", rslt);

    /* Upload the configuration file to enable the features of the sensor. */
    rslt = bma456_tablet_write_config_file(&bma4);
    bma4_error_codes_print_result("bma456_tablet_write_config", rslt);

    /* Accelerometer configuration Setting */
    /* Output data Rate */
    accel_conf.odr = BMA4_OUTPUT_DATA_RATE_50HZ;

    /* Gravity range of the sensor (+/- 2G, 4G, 8G, 16G) */
    accel_conf.range = BMA4_ACCEL_RANGE_2G;

    /* The bandwidth parameter is used to configure the number of sensor samples that are averaged
     * if it is set to 2, then 2^(bandwidth parameter) samples
     * are averaged, resulting in 4 averaged samples
     * Note1 : For more information, refer the datasheet.
     * Note2 : A higher number of averaged samples will result in a less noisier signal, but
     * this has an adverse effect on the power consumed.
     */
    accel_conf.bandwidth = BMA4_ACCEL_NORMAL_AVG4;

    /* Enable the filter performance mode where averaging of samples
     * will be done based on above set bandwidth and ODR.
     * There are two modes
     *  0 -> Averaging samples (Default)
     *  1 -> No averaging
     * For more info on No Averaging mode refer datasheet.
     */
    accel_conf.perf_mode = BMA4_CIC_AVG_MODE;

    /* Set the accel configurations */
    rslt = bma4_set_accel_config(&accel_conf, &bma4);
    bma4_error_codes_print_result("bma4_set_accel_config status", rslt);

    /* NOTE : Enable accel after set of configurations */
    rslt = bma4_set_accel_enable(BMA4_ENABLE, &bma4);
    bma4_error_codes_print_result("bma4_set_accel_enable status", rslt);

    /* Mapping data ready interrupt with interrupt pin 1 to get interrupt status once getting new accel data */
    rslt = bma456_tablet_map_interrupt(BMA4_INTR1_MAP, BMA4_DATA_RDY_INT, BMA4_ENABLE, &bma4);
    bma4_error_codes_print_result("bma456_tablet_map_interrupt status", rslt);

    printf("\nAXIS_REMAP_FUNC_TEST 1\n");
    printf("Get sensor data of re-mapped axes\n");

    rslt = bma456_tablet_get_remap_axes(&remap_data, &bma4);
    bma4_error_codes_print_result("bma456_tablet_get_remap_axes", rslt);

    printf("Re-mapped x value = %s\n", data_array[remap_data.x]);
    printf("Re-mapped y value = %s\n", data_array[remap_data.y]);
    printf("Re-mapped z value = %s\n", data_array[remap_data.z]);

    printf("Expected Re-mapped x value = BMA4_X\n");
    printf("Expected Re-mapped y value = BMA4_Y\n");
    printf("Expected Re-mapped z value = BMA4_Z\n");

    if ((remap_data.x == BMA4_X) && (remap_data.y == BMA4_Y) && (remap_data.z == BMA4_Z))
    {
        printf(">> PASS\n");
    }
    else
    {
        printf(">> FAIL\n");
    }

    printf("Print mapped data\n");

    for (;;)
    {
        /* Read interrupt status */
        rslt = bma456_tablet_read_int_status(&int_status, &bma4);
        bma4_error_codes_print_result("bma456_tablet_read_int_status", rslt);

        /* Filtering only the accel data ready interrupt */
        if ((rslt == BMA4_OK) && (int_status & BMA4_ACCEL_DATA_RDY_INT))
        {
            rslt = bma4_read_accel_xyz(&accel, &bma4);
            bma4_error_codes_print_result("bma4_read_accel_xyz", rslt);

            printf("Accel :: X = %d Y = %d Z = %d\n", accel.x, accel.y, accel.z);

            break;
        }
    }

    printf("\nAXIS_REMAP_FUNC_TEST 2\n");
    printf("Get sensor data of re-mapped axes\n");

    remap_data.x = BMA4_NEG_Y;
    remap_data.y = BMA4_Z;
    remap_data.z = BMA4_NEG_X;

    rslt = bma456_tablet_set_remap_axes(&remap_data, &bma4);
    bma4_error_codes_print_result("bma456_tablet_set_remap_axes", rslt);

    if (rslt == BMA4_OK)
    {
        rslt = bma456_tablet_get_remap_axes(&remap_data, &bma4);
        bma4_error_codes_print_result("bma456_tablet_get_remap_axes", rslt);

        if (rslt == BMA4_OK)
        {
            printf("Re-mapped x value = %s\n", data_array[remap_data.x]);
            printf("Re-mapped y value = %s\n", data_array[remap_data.y]);
            printf("Re-mapped z value = %s\n", data_array[remap_data.z]);
        }

        printf("Expected Re-mapped x value = BMA4_NEG_Y\n");
        printf("Expected Re-mapped y value = BMA4_Z\n");
        printf("Expected Re-mapped z value = BMA4_NEG_X\n");

        if ((remap_data.x == BMA4_NEG_Y) && (remap_data.y == BMA4_Z) && (remap_data.z == BMA4_NEG_X))
        {
            printf(">> PASS\n");
        }
        else
        {
            printf(">> FAIL\n");
        }
    }

    printf("Print mapped data\n");

    for (;;)
    {
        /* Read interrupt status */
        rslt = bma456_tablet_read_int_status(&int_status, &bma4);
        bma4_error_codes_print_result("bma456_tablet_read_int_status", rslt);

        /* Filtering only the accel data ready interrupt */
        if ((rslt == BMA4_OK) && (int_status & BMA4_ACCEL_DATA_RDY_INT))
        {
            rslt = bma4_read_accel_xyz(&accel, &bma4);
            bma4_error_codes_print_result("bma4_read_accel_xyz", rslt);

            printf("Accel :: X = %d Y = %d Z = %d\n", accel.x, accel.y, accel.z);

            break;
        }
    }

    printf("\nAXIS_REMAP_FUNC_TEST 3\n");
    printf("Get sensor data of re-mapped axes - 2nd combination\n");

    remap_data.x = BMA4_NEG_Z;
    remap_data.y = BMA4_NEG_X;
    remap_data.z = BMA4_Y;

    rslt = bma456_tablet_set_remap_axes(&remap_data, &bma4);
    bma4_error_codes_print_result("bma456_tablet_set_remap_axes", rslt);

    if (rslt == BMA4_OK)
    {
        rslt = bma456_tablet_get_remap_axes(&remap_data, &bma4);
        bma4_error_codes_print_result("bma456_tablet_get_remap_axes", rslt);

        if (rslt == BMA4_OK)
        {
            printf("Re-mapped x value = %s\n", data_array[remap_data.x]);
            printf("Re-mapped y value = %s\n", data_array[remap_data.y]);
            printf("Re-mapped z value = %s\n", data_array[remap_data.z]);
        }

        printf("Expected Re-mapped x value = BMA4_NEG_Z\n");
        printf("Expected Re-mapped y value = BMA4_NEG_X\n");
        printf("Expected Re-mapped z value = BMA4_Y\n");

        if ((remap_data.x == BMA4_NEG_Z) && (remap_data.y == BMA4_NEG_X) && (remap_data.z == BMA4_Y))
        {
            printf(">> PASS\n");
        }
        else
        {
            printf(">> FAIL\n");
        }
    }

    printf("Print mapped data\n");

    for (;;)
    {
        /* Read interrupt status */
        rslt = bma456_tablet_read_int_status(&int_status, &bma4);
        bma4_error_codes_print_result("bma456_tablet_read_int_status", rslt);

        /* Filtering only the accel data ready interrupt */
        if ((rslt == BMA4_OK) && (int_status & BMA4_ACCEL_DATA_RDY_INT))
        {
            rslt = bma4_read_accel_xyz(&accel, &bma4);
            bma4_error_codes_print_result("bma4_read_accel_xyz", rslt);

            printf("Accel :: X = %d Y = %d Z = %d\n", accel.x, accel.y, accel.z);

            break;
        }
    }

    printf("\nAXIS_REMAP_FUNC_TEST 4\n");
    printf("Get sensor data of re-mapped axes - 3rd combination\n");

    remap_data.x = BMA4_Y;
    remap_data.y = BMA4_Z;
    remap_data.z = BMA4_X;

    rslt = bma456_tablet_set_remap_axes(&remap_data, &bma4);
    bma4_error_codes_print_result("bma456_tablet_set_remap_axes", rslt);
    if (rslt == BMA4_OK)
    {
        rslt = bma456_tablet_get_remap_axes(&remap_data, &bma4);
        bma4_error_codes_print_result("bma456_tablet_get_remap_axes", rslt);

        if (rslt == BMA4_OK)
        {
            printf("Re-mapped x value = %s\n", data_array[remap_data.x]);
            printf("Re-mapped y value = %s\n", data_array[remap_data.y]);
            printf("Re-mapped z value = %s\n", data_array[remap_data.z]);
        }

        printf("Expected Re-mapped x value = BMA4_Y\n");
        printf("Expected Re-mapped y value = BMA4_Z\n");
        printf("Expected Re-mapped z value = BMA4_X\n");

        if ((remap_data.x == BMA4_Y) && (remap_data.y == BMA4_Z) && (remap_data.z == BMA4_X))
        {
            printf(">> PASS\n");
        }
        else
        {
            printf(">> FAIL\n");
        }
    }

    printf("Print mapped data\n");

    for (;;)
    {
        /* Read interrupt status */
        rslt = bma456_tablet_read_int_status(&int_status, &bma4);
        bma4_error_codes_print_result("bma456_tablet_read_int_status", rslt);

        /* Filtering only the accel data ready interrupt */
        if ((rslt == BMA4_OK) && (int_status & BMA4_ACCEL_DATA_RDY_INT))
        {
            rslt = bma4_read_accel_xyz(&accel, &bma4);
            bma4_error_codes_print_result("bma4_read_accel_xyz", rslt);

            printf("Accel :: X = %d Y = %d Z = %d\n", accel.x, accel.y, accel.z);

            break;
        }
    }

    printf("\nAXIS_REMAP_FUNC_TEST 5\n");
    printf("Get sensor data of re-mapped axes - 4th combination\n");

    remap_data.x = BMA4_NEG_X;
    remap_data.y = BMA4_NEG_Y;
    remap_data.z = BMA4_NEG_Z;

    rslt = bma456_tablet_set_remap_axes(&remap_data, &bma4);
    bma4_error_codes_print_result("bma456_tablet_set_remap_axes", rslt);

    if (rslt == BMA4_OK)
    {
        rslt = bma456_tablet_get_remap_axes(&remap_data, &bma4);
        bma4_error_codes_print_result("bma456_tablet_get_remap_axes", rslt);

        if (rslt == BMA4_OK)
        {
            printf("Re-mapped x value = %s\n", data_array[remap_data.x]);
            printf("Re-mapped y value = %s\n", data_array[remap_data.y]);
            printf("Re-mapped z value = %s\n", data_array[remap_data.z]);
        }

        printf("Expected Re-mapped x value = BMA4_NEG_X\n");
        printf("Expected Re-mapped y value = BMA4_NEG_Y\n");
        printf("Expected Re-mapped z value = BMA4_NEG_Z\n");

        if ((remap_data.x == BMA4_NEG_X) && (remap_data.y == BMA4_NEG_Y) && (remap_data.z == BMA4_NEG_Z))
        {
            printf(">> PASS\n");
        }
        else
        {
            printf(">> FAIL\n");
        }
    }

    printf("Print mapped data\n");

    for (;;)
    {
        /* Read interrupt status */
        rslt = bma456_tablet_read_int_status(&int_status, &bma4);
        bma4_error_codes_print_result("bma456_tablet_read_int_status", rslt);

        /* Filtering only the accel data ready interrupt */
        if ((rslt == BMA4_OK) && (int_status & BMA4_ACCEL_DATA_RDY_INT))
        {
            rslt = bma4_read_accel_xyz(&accel, &bma4);
            bma4_error_codes_print_result("bma4_read_accel_xyz", rslt);

            printf("Accel :: X = %d Y = %d Z = %d\n", accel.x, accel.y, accel.z);

            break;
        }
    }

    bma4_coines_deinit();

    return rslt;
}